thankfully the camerawork doesnt really show the welds that well
| bmwkraftur.is https://bmwkraftur.is/spjall/ |
|
| E30 M3 Europa(RUST)Meister https://bmwkraftur.is/spjall/viewtopic.php?f=5&t=47713 |
Page 21 of 21 |
| Author: | slapi [ Tue 02. Dec 2014 15:55 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Just remember to orientate the adjusment bolts in the same direction to get the thrust angle right , people have been failing on that |
|
| Author: | fart [ Tue 02. Dec 2014 16:05 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
thankfully the camerawork doesnt really show the welds that well
|
|
| Author: | bimmer [ Tue 02. Dec 2014 16:48 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
fart wrote: thankfully the camerawork doesnt really show the welds that well Ouch...... |
|
| Author: | fart [ Tue 02. Dec 2014 16:54 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
bimmer wrote: fart wrote: thankfully the camerawork doesnt really show the welds that well Ouch...... hehe 
|
|
| Author: | Zorba [ Tue 02. Dec 2014 20:25 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
fart wrote: bimmer wrote: fart wrote: thankfully the camerawork doesnt really show the welds that well Ouch...... hehe 
|
|
| Author: | Zorba [ Fri 30. Jan 2015 21:09 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Small update. . . Got access to this today.....  .... and managed to get on with some welding with a lil help..... Subframe repaired and reinforced: Had to cut the bottom reinforcements to access the back   Then new plates welded in...  The top had to be filled in....    and then smoothed...  Finally the uter ones were welded back on ...  Then we did the ARB mount holes: I mounted the reinforcements and secured them with a 10mm bolt:  Then welded all around and smoothed the welds (should look much better after paint):   The otherside was much worse as i had to remove some of the rusted area:  I am debating if i should leave it as it is or close it. As far as I know this holes only act as drains so it may be better to have them slightly larger. What do you guys think? Should be getting blasted again tomorrow and then painted. 
|
|
| Author: | Alpina [ Fri 30. Jan 2015 23:40 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Weld,,,,,,,,,,,,,,,, meister ? |
|
| Author: | Zorba [ Sat 31. Jan 2015 00:18 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Alpina wrote: Weld,,,,,,,,,,,,,,,, meister ? 
|
|
| Author: | Angelic0- [ Sat 31. Jan 2015 16:15 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Incredible craftsmanship  
|
|
| Author: | Zorba [ Fri 20. Feb 2015 09:21 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Some small progress..... Steering rack was taken completely apart .....  and parts painted and cleaned....    New seals replaced.....  And started putting it back.... I am still trying to find new bearings for it but seems like even the dealer can not find them. The bearings are the ones circled in the below pic (altough the one I really want to replace is No.57  Worst case scenario I will reuse the old ones but if you guys know a part number or where to get new ones please let me know! |
|
| Author: | tinni77 [ Fri 20. Feb 2015 21:51 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
Just take the bearing to Fálkinn and they will take care of you.. OE Quality stuff there+excellent service |
|
| Author: | Zorba [ Sat 21. Feb 2015 16:39 ] |
| Post subject: | Re: E30 M3 Europa(RUST)Meister |
tinni77 wrote: Just take the bearing to Fálkinn and they will take care of you.. OE Quality stuff there+excellent service I already did that ....and they dont have anything like that |
|
| Page 21 of 21 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|